1. Parts
  2. Engine

2001 Harley-Davidson Electra Glide Ultra Classic - FLHTCUI Engine

2001 Harley-Davidson Electra Glide Ultra Classic - FLHTCUI
Oil Filter:
KN-171B
Select Your Ride: Go

Refine
Reset
Sort By:
Grid List
Quick View
S&S Cycle Adjustable Pushrod Kit Adjustable pushrod kit includes all components required to convert a stock height Twin Cam style engine to adjustable pushrods and pushrod covers These adjustabl...
Quick View
S&S Cycle Super Stock Cylinder Head Kit Readily bolts on and accepts most stock components except head bolts and some rocker boxes  Stock rocker boxes will not work if S&S Cycle electric compress...
Quick View
S&S Cycle 551 Grind Easy Start Cam Start any engine with a stock starter Save your starter and battery Reliable-tested for 10,000 starts and didn't even run the battery down Automatic - no buttons ...
Quick View
S&S Cycle 640 Grind Easy Start Cams Each of the 2 exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heel" of the cam at the point where the valve would normally b...
Quick View
S&S Cycle 551 Grind Cam 551 cams are bolt-in cams for 2005-up engines. Cams that exceed the limits of the stock valve springs require the use of special high lift springs. Most S&S cams have higher...
Quick View
S&S Cycle Rocker Cover Kit Highest Quality castings Accepts valve springs up to 1.660 O.D. and .710 valve heights Includes Viton O-rings, all necessary hardware and gaskets required for install...
Quick View
Feuling HP+ Oil Pump Billet 6061 aluminum Increases oil pressure No more oily air cleaners Eliminates blow by and wet sumping More horsepower and torque to the rear wheel Fits both A and B Twin Ca...
Quick View
Andrews Products Adjustable PushrodsA must have for easy and painless cam changes. No interference, 7/16" diameter for strength Cut-out OEM rods for easy removal Sold in sets of 4 Made in the U.S....
Quick View
S&S Cycle 640G Grind Cams   Designed for engines of 95" or more with compression ratios between 10.5:1 and 11.5:1 used in S&S 124" engines
Quick View
S&S Cycle 585 Grind Easy Start Cam Each of the 2 exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heel" of the cam at the point where the valve would normally be...
Quick View
Kuryakyn
Bluegrass Breather Kit
$49.99
You save $5.00 (9%)
  • Black
(0)
Kuryakyn Bluegrass Breather KitUnfortunately, almost all Harley-Davidson engines that vent the crankcase through the cylinder heads also expel oil through the same passages. Venting directly into t...
Quick View
S&S Cycle 585 Grind Easy Start Cams Each of the 2 exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heel" of the cam at the point where the valve would normally b...
Quick View
S&S Cycle 570 Grind Easy Start Cams Each of the 2 exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heel" of the cam at the point where the valve would normally b...
Quick View
S&S Cycle 97" Big Bore Kit The 97" Big Bore kit for 88" motors yield excellent results with stock cylinder heads Feature the largest bore (3.927") that can safely be used in a cylinder with stoc...
Quick View
S&S Cycle 583 Grind Easy Start Cam Each of the 2 exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heel" of the cam at the point where the valve would normally be...

Latest Reviews

Michael (Monterey )

Fit
Quality
Installation
Recommend

Naval Officer

Arrived on time, does the job, for market price (which I think is too high for the part, but it is the price the market will allow--so in that regard it is fair-ish). Nevertheless, M/C SuperStore always comes through with what I need, when I need it, with no b/s. That's 5-star in my book...

robert (Avon )

Fit
Finish
Durability
Features
Cost Benefit

Not correct

So, if you order this tool for a Yamaha 450, be careful. This is NOT the correct part.

Rico (Buck Ridge )

Fit
Quality
Installation
Recommend

Perfect Fit

I have a 2014 Harley Davidson Street Glide. This cap fit my bike perfectly. If it doesn't fit your bike, then sell it and buy a Street Glide.

Dean (Livonia )

Fit
Quality
Installation
Recommend

Braided Oil Line Kit for 98 FLSTC

A little tricky at first to figure out without instructions but after a little tinkering they installed almost flawlessly. Had to machine the oil pump input fitting to fit, hit the side of the pump casing when installing.

Robert (Cresco )

Fit
Quality
Installation
Recommend

Cobra oil dipstick

Great looking on the bike. Difficult to see oil level on it.

;
Back to Top