1. Motorcycle Parts
    2. Engine
    3. Cruiser Engine

    Cruiser Motorcycle Engine

    Refine
    Grid List
    BikeMaster
    Magnetic Steel Oil Drain Plug
    $10.35
    $9.99
    You save $0.36 (3%)
    (10)
    BikeMaster Magnetic Steel Oil Drain Plug It's hard to believe that a little bolt with a magnet can improve the performance and lifespan of your motorcycle. BikeMaster's Magnetic Oil Drain plug will
    Andrews Products EV27 Grind Cam Andrews Products grinds its cams with the help of a computer with cam design capabilities. This superior technology gives the utmost in both performance and r
    Cobra
    Billet Oil Cap
    $29.95
    $25.46
    You save $4.49 (15%)
    (6)
    Cobra Billet Oil Cap Designed to replace unsightly stock oil caps Cobra's best billet bits are machined right and made to fit just like they came from the OEM Made in the U.S.A.
    Andrews Products "C" Grind Cam Andrews Products grinds its cams with the help of a computer with cam design capabilities. This superior technology gives the utmost in both performance and rel
    S&S Cycle 106" Big Bore Kit At 3.927? bore, these cylinders have the largest bore that S&S feels can safely be used in a cylinder with stock spigot diameter This kit is only offered with S&S cylin
    S&S Cycle 475G Grind Cams   Designed as a bolt in stock replacement cam for rides with stock 1999-06 engines who are not looking for more power, but want to eliminate the stock cam drive chains.
    S&S Cycle 509C Grind Cam Designed as a bolt in, high torque cam for 99-06 models, 180  psi cranking compression, no need for compression releases For 88" CID engines with stock compression ratio idle
    S&S Cycle 509G Grind Cams  Designed as a bolt in, high torque cam for 99-06 models. 180 psi cranking compression, no need for compression releases. For 88" CID engines with stock compression ratio Idl
    S&S Cycle 510 Grind Cam Designed as a bolt in cam for 88" to 103" engines with compression ratios below 9.7:1 Intended primarily for stock heads that have not been ported
    S&S Cycle 510G Grind Cams Designed as a bolt in cam for 88" to 103" engines with compression rations belows 9.7:1 Intended primarily for stock heads that have not been ported
    S&S Cycle 551 Grind Cam 551 cams are bolt-in cams for 2005-up engines. Cams that exceed the limits of the stock valve springs require the use of special high lift springs. Most S&S cams have higher li
    S&S Cycle 551 Grind Easy Start Cam Start any engine with a stock starter Save your starter and battery Reliable-tested for 10,000 starts and didn't even run the battery down Automatic - no buttons to
    S&S Cycle 551 Grind Easy Start CamsEach of the 2 exhaust cam lobes are equipped with a spring loaded compression release lobe on the "heel" of the cam at the point where the valve would normally be fu
    S&S Cycle 557 Grind Easy Start Cam S&S specifically developed the new bolt-in 557 Easy Start cams for the Tri Glide. The short duration produces lots of torque, and the automatic mechanical compressio

    Latest Reviews

    Robert (Cresco, IA)

    Fit
    Quality
    Installation
    Recommend

    Cobra oil dipstick

    Great looking on the bike. Difficult to see oil level on it.

    Davey (South Central, WI)

    Fit
    Quality
    Installation
    Recommend

    Great Deal

    2008 FZ1- Fit perfectly, no 'big glob of glue' on the end holding the magnet in. Nice black finish, we'll see if it holds up. Same exact length as stock. I'm actually kind of excited to see what it pulls out of the oil at the next interval. Cheap insurance, money well spent!

    Peter (Northbrook, IL)

    Fit
    Quality
    Installation
    Recommend

    Waste of money!

    Bought this to make it easier to check the oil. Followed instructions precisely. Problem is the cap is poorly manufactured for an exact fit. The lip that is supposed to catch and lock the cap to the base does not fit. So the cap just sits on top of the base and pops right off as soon as the engine is started. Total waste of time, money and energy. This is the second Kuryakyn product that has been a major disappointment. I am going to consider that before buying anything more from them!

    tlock28 (Highland City, FL)

    Fit
    Quality
    Installation
    Recommend

    temp stick

    My stock dip stick was leaking and had chipped crome on the cover. Found this and liked the temp gauge add on. Works fine and would recommend this.

    Keep your cruiser roaring down the highway with cruiser engine parts from Motorcycle Superstore. The power of the motor is what gives you freedom on the open road, so don’t neglect your bike’s power-plant. Whether you are performing routine maintenance or trying to increase power, Motorcycle Superstore has all the engine parts you’ll need for your hog. Find great deals on parts like oil filters, clutches, gaskets, camshafts, cylinders and more, all here under one roof. To easily find the cruiser engine parts you need, check out our bike part finder. Also, use our options filters to narrow our selection even more by price, style and brand. Get the power you need for your cruiser with engine parts from Motorcycle Superstore.
    Back to Top