Motion Pro Pilot Screw Adjusting Tool

Was $25.99 $23.39 You save $2.60 (10%)

Rating 4.44 of 5 (10 Reviews)

This Product Qualifies for Free Shipping

In Stock
Unavailable

Qty:

Product Information

Motion Pro Pilot Screw Adjusting Tool

  • 110° angled head for hard-to-reach pilot screws extends reach 1"
  • Fits most applications
  • 17" length
  • Straight-slot blade tip
  • Item # 4969
  • SKU #
  • Mfr. Part #

Product Reviews 1 - 10 of 10

Overall Rating: 4.44 of 5

(10 Reviews)
5
5
4
4
3
0
2
0
1
1
What Other Riders Are Saying...

Fit

Finish

Durability

Features

Cost Benefit

carb adjusting

great tool-did not work on my 1998 750 nighthawk-not enough room to use it?

randy - April 20, 2012

(lancaster, OH)

Fit

Finish

Durability

Features

Cost Benefit

Didn't do the job.

Didn't work; tried to modify it to work. Still doesn't work. Waste of money. Should have spent the $65 for the good one with the gear drive.

Gary H. - November 28, 2011

(Missoula, MT)

Fit

Finish

Durability

Features

Cost Benefit

Pilot Screw

Great product. The screwdriver end was too long, but with a pipe cutter I cut one inch off the end and now it fits everything and works great! Well-made product, just should offer it in two lengths for tight areas! Don't be afraid to cut it shorter, won't hurt the product at all!

Greg M. - November 18, 2011

(Piscataway, NJ)

Fit

Finish

Durability

Features

Cost Benefit

Works great!!

Much easier to get to those hard to reach middle carbs/throttle bodies.

Skip - September 29, 2011

(Overton, TX)

Fit

Finish

Durability

Features

Cost Benefit

Surprise, it works!

The pilot screw on the #2 carb of my 4cyl. Kawasaki was unreachable by hand using even the short screwdriver bits. Just not enough room for my hand to reach in and do the work. This tool just barely works, but it does work! Worth every penny I paid.

James M. - September 26, 2011

(Asheville, NC)

Fit

Finish

Durability

Features

Cost Benefit

Bent screwdriver did the job

I was able to access all four pilot screws on my ‘81 Goldwing Interstate. It took some practice. Worth the price.

Arnold H. - November 29, 2010

(Boise, ID)

Fit

Finish

Durability

Features

Cost Benefit

Does not fit KLR 650 or KL250 Super Sherpa

Nice lookin' tool, just won't fit any of my bikes. The clearance needed below bottom of carb is something around 1.5 inches. Not gonna happen without rotating the carb around.

Tyler S - June 29, 2010

(Lynchburg, VA)

Fit

Finish

Durability

Features

Cost Benefit

Great

Best thing since sliced bread when needing to adjust the air on the carb.

JC - May 5, 2010

(Old Hickory, TN)

Fit

Finish

Durability

Features

Cost Benefit

Quality Tool

Couldn't use for what I wanted, but will find many uses in the future. Made of high quality material.

Guns - December 3, 2009

(Jacksonville, FL)

Fit

Finish

Durability

Features

Cost Benefit

Works like a charm

I had been looking for this tool for about 2 years for a reasonable price. After re-jetting the carbs I needed this tool to fine tune the idle. After the adjustments were made the bike runs perfect. A must have if you mess with your carbs in any way.

Bill - August 11, 2008

(Exton, PA)