-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
rvaBV (Richmond, VA)
07' crf250x
This product fit my bike fine with no mods. I tested it out for the first time in the off-road mountain trails of WVA. The continuous wrap-around plastic design is a must!
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Gabriel (McAllen, TX)
Acerbis Handguards
I Bought a KTM 2012 350 xcf-w and these hand guards fit great, are easy to install and my hands feel protected big time. I would recommend this product to anyone.
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
TNT (Salt lake City, UT)
Acerbis Pro X Strong
I've had several sets and it's true the instructions are a lacking for first timers! For the money they are hard to beat. Cycra's are bigger with replaceable plastic and more adjustable mounting hardware and are more expensive. So it's rider's choice as to which they prefer! I need them as I am vertically challenged and tip over in the mountains on the clutch side quite often. LOL TNT
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Bill (Nampa, ID)
Acerbis Handguards
This new set went on my new KTM. Fit well with a little adjusting of the levers. I know they work well for their intended use (protection against brush, limbs. etc) because this is my third set. They look great with a good color match. They do scratch easy.
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Steve F (Liberty, SC)
RALLY PRO
2012 KTM xcw, I had to modify the hardware a little bit but, over all they do a good job. Just a few light hits and drops but, no major hits. Still cheaper than replacing broke levers!!!
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Eric (Tracy, CA)
Great guards
Very nice guards, mounting was a bit awkward on the brake side..I think I will try a different style of mounting hardware. Look great!
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
John (Chicago, IL)
Good so far
I installed these on my 2008 YZ250F with stock 1-1/8" pro-tapers. The kit comes with two sets of bushings for use with mounting the bracket on the front of the bars. They ended up right across the bends on the bars. Neither bushing would work. I installed without any bushings and it actually fit quite well. I went down once so far...not very hard...so far they are working well.
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Carl (San Antonio, TX)
Not a good fit for a 2011 Yamaha YZ250F
I tried to mount these with the optional Acerbis triple clamp mount (see my review for it), but the mount did not fit my bike. The handlebar mounts with this kit interfere too much with number plate (the reason I wanted to mount to triple clamp mount), and thus I will not use these. I will resell at a big loss.
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Tom B. (Meridian, ID)
Hand Guards
These hand guards work perfectly and are very strong. I like the lower profile they offer. This lower profile still offers great protection against all the brushy trails I've ridden on, so far nothing has gotten through.
-
Fit
-
Finish
-
Durability
-
Features
-
Cost Benefit
Curtis C. (kaneohe, HI)
Acerbis Handguards
Fit is good on my yz125 and yz250. The profile is perfect. The bar end clamps are the best. The inside clamps fit up good on most handle bars.
