1. Cruiser Motorcycle
    2. Parts
    3. Hand Controls

    2009 Harley-Davidson Road King - FLHR Handlebar Risers

    2009 Harley-Davidson Road King - FLHR
    Tire Size:
    Front: 130/80-17, Rear: 180/65-16
    Spark Plug:
    DCPR7E
    Battery:
    YIX30L
    Stock Chain/Belt:
    140T
    Stock Gearing:
    Front: 32T, Rear: 68T
    Oil Filter:
    KN-171B
    Select Your Ride:Go
    Refine
    Grid List
    1-8 of 8
    Roland Sands Design
    Nostalgia Risers
    $159.95 - $169.95
    $147.99 - $158.99
    You save up to $10.96 (6%)
    (0)
    Roland Sands Design Nostalgia Risers Two bolt and four bolt risers accepts stock or aftermarket 1" diameter handlebars Four bolt riser accepts stock or aftermarket 1-1/4" diameter handlebars All styl
    Roland Sands Design
    1" Handlebar Risers
    $159.95 - $169.95
    $143.99 - $152.99
    You save up to $16.96 (10%)
    (0)
    R S D 1" Handlebar Risers CNC-machined from billet aluminum Laser-engraved RSD logo on top riser cap Available in Black Anodized or Chromed finish Drilled and tapped for ½ "-13 mounting bolt (not inc
    Biker's Choice
    1-1/2" Fat Riser Bars
    $219.95
    $186.96
    You save $32.99 (15%)
    (0)
    Biker's Choice 1-1/2" Fat Riser Bars Bars are 1 1/2" thick and 31.5” wide Risers are 3 1/2" centers and available in 7 and 9 inch heights Pre-drilled, dimpled for internal wiring Work
    Biker's Choice
    1-1/4" Fat Riser Bars
    $169.95
    $144.46
    You save $25.49 (15%)
    (0)
    Biker's Choice 1-1/4" Fat Riser Bars Bars are 1 1/4" thick, 31” wide, with a 8-1/2” center width. Risers are 3 1/2" centers and available in 6, 8, and 10 inch heights Pre-dril
    Roland Sands Design
    Misano Riser Hole Plugs
    $38.95 - $38.99
    $35.10 - $35.99
    You save up to $3.89 (10%)
    (0)
    Roland Sands Design Misano Riser Hole Plugs When installing clip ons use Misano race styled riser hole plugs to clean up the holes in the top of your stock triple clamp Designed to match RSD Misano f
    Biltwell Stainless Steel Slimline RisersConstruction: Investment-cast and CNC-machined stainless steel. 5/16" x 18 t.p.i. Stainless steel bar clamp hardware.Fitment: Slimline risers have 1-3/4" of ris

    Latest Reviews

    Matthew (Elizabethtown, KY)

    Fit
    Quality
    Installation
    Recommend

    exactly what wanted

    The feel of these grips is awesome! The metal finish is very nice! There are no blemishes in the chrome polish and all the rubber is perfect- no air bubbles or any goofy mess. The only problem I had with installation was the super glue dried very, very, very fast! If you don't mark it, it will be wrong. It was a good thing I did because it took literally 10 seconds for it to set. Other than that everything else is absolutely perfect.

    Bob (Auburndale , FL)

    Fit
    Quality
    Installation
    Recommend

    Water Resistant GPS Pouch with Handlebar Mount

    I had to modify the product plus add tape to the handle bar to get it tight. It fits my TomTom just fine, my cable fits fine, it has a short peg tail connector so it is easy to un-plug. The only problem is you can't see it in the bright sun here in FL unless you pull over and get in the shade someplace and reroute or what ever you want to do and then zip it back up and off you go. I rode for 2 1/2 hours last night and it worked perfectly, easy to see and hear on my 2007 Ultra Glide.

    Bobby (Talbott, TN)

    Fit
    Quality
    Installation
    Recommend

    Black on Black ISO GRIPS 2002 Nomad

    Great product, easy to install, and looks great. The most difficult part of the installation was removing the old grip in the left. Throttle side was much easier than I expected. The left side fit so snugly that the glue was not necessary. Vibration was never a problem, but the larger, softer grip feels much more comfortable. I'd definitely recommend these.

    nomad (Covelo, CA)

    Fit
    Quality
    Installation
    Recommend

    All Balls neck bearings inferior

    After looking at bearing set I went with OEM bearings. Easier to install and better steel. All Ball bearings felt and looked cheaper and were manufactured from less quality steel. To return is not cost effective.

    A. C. (Louisville, CO)

    Fit
    Quality
    Installation
    Recommend

    Show Chrome Beverage Holder

    Very good quality and materials, easy to install, and appears to work very well. Some concern about liquid draining from the holder in inclement weather.

    Back to Top