1. Parts
  2. Exhaust
  3. Exhaust Accessories

2013 Harley-Davidson Road Glide Custom - FLTRX Exhaust Accessories

2013 Harley-Davidson Road Glide Custom - FLTRX
Tire Size:
Front: 130/70-18, Rear: 180/65-16
Spark Plug:
DCPR7E
Battery:
YIX30L
Stock Chain/Belt:
140T
Stock Gearing:
Front: 32T, Rear: 68T
Oil Filter:
KN-171B
Select Your Ride: Go

Refine
Reset
Sort By:
Grid List
Biltwell Iron Exhaust Flange Set Construction: Cold-rolled 16-gauge (0.060"/1.5mm) x 1-3/4" O.D. high-tensile steel tubing, raw finish. One tube (two ends) per order. Each tube includes 2 header fl...
Kuryakyn
Muffler Bracket Covers
$35.99
You save $4.00 (10%)
  • Chrome
(0)
Kuryakyn Muffler Bracket Covers Designed to encapsulate & smooth the appearance of the welded on muffler mounting brackets beneath the saddlebags for a streamlined look. Made from chrome plated sta...
Biltwell Exhaust Builder's Pipe Kit WHAT'S HERE: Our Builder Exhaust Kit is exactly what its name implies: a selection of pre-fabbed tubing, header flanges and exhaust tips that puts the art of cus...
Vance & Hines
O2 Sensor Harness Extension
$26.99
You save $2.96 (9%)
  • Black
(0)
Vance & Hines O2 Sensor Harness Extension 6" extension harness Reduces the 18mm O2 bungs on 09 models to 12mm O2 bungs on 10-13 models No cutting or splicing required Made in the U.S.A.
Crusher
Power Cell Heat Shield
$71.99
You save $8.00 (10%)
  • Chrome
(0)
Crusher Power Cell Heat ShieldIf you already have a Crusher Power Cell Exhaust System, but you're yearning for more chrome, here's a fully chromed replacement cover. Chrome replacement heat shields...

Latest Reviews

Michael (Lake Munmorah )

Fit
Finish
Durability
Features
Cost Benefit

Vance & Hines fitment on 2007 Suzuki C50 Boulevard Warning!

I just fitted the Vance & Hines Slash staggered to my Boulevard C50 and found that there is discrepancies between the header flanges to the rear fastening plate by as much as 5mm gap after tightening the headers to the engine exhaust ports now this may not sound serious but the fact is that if you were to tighten the rear exhaust plate to the bikes main exhaust mounting, you will certainly put stress on the engine header and pipes full time. To avoid this problem you will need to 1. when fitting tightening the header flanges exhaust make sure they seat flat on engine ports first. 2. then check the rear plate gap between the exhaust plate and bikes mounting plate, if required pack the gap with washers then tighten plate bolts 3. Check Brake pedal lever clearance and move the footrest downward by releasing the bolts and placing a 2mm thick half washer on top of the bolts between the frame and footrest plate bolts to clear the front pipe shield and then you are set to go, well almost 4. Your Heat Oxygen sensor must be put back on the rear cylinder pipe #1 if you don't want to cut or disable pin 23, It is best to leave your ECU alone, Enjoy!!

Dan (Kelso )

Fit
Quality
Sound
Install
Performance

Good Fit And Finish

I have a 2011 FLHTK. The headers look great on the bike. They are quite a bit louder than stock, when you get on the gas. I didn't think the install was as difficult as some of the reviews state. Although, the pictures could be better. Make sure to read all instructions first.

Jerry (Roswell )

Fit
Quality
Sound
Install
Performance

Best investment!

I purchased these for my 2009 Street Bob. They took a couple days to ship out, but actually arrived a day early because of UPS. They went right on and the bike runs great and sounds great. Did not have to buy a fuel management system like most dealers will tell you that you must buy or the bike will run lean. The best investment I have made for my bike.

Rex (Frankfort )

Fit
Quality
Installation
Recommend

Bassani Firepower mufflers are great

The quality of build is equal to the HD factory parts. I did however need to use the factory attachment screws as the new ones didn't work. The sound is very powerful. Sounds like the bigger motored HD bikes now. It is very different from stock even at idle. The power increase...is unmistakeable. These pipes add about 10% more HP and Torque over stock according to a dyno test I read online. I think that might be conservative. My bike is stock otherwise.

Johnny (Eatonton )

Fit
Quality
Installation
Recommend

Nice Addition

Great fit, sound and appearance. I didn't want something so loud it would be an annoyance to the neighbors, but wanted it to sound like a Harley. I had them installed in lest than 15 minutes and it was a nice addition in sound to my 2014 Ultra Limited. I like them a lot.

;
Back to Top